Tuning A Rc Nitro Engine For Optimal Power - A Guide For Beginners
- Date: 2008-08-26 - Word Count: 621
Share This!
When I first started racing Gas Powered RC cars, I used to struggle to get the engine into tune, while I was able to get the engine to start on a dime and it used to run fine for almost an entire fuel tank, it always seemed to over-heat near the end of the run. After many hours out on the track I can now finally say that I've got it down, tuning for me is now a 5 minute operation before I take my RC car out, and once it's dialed in I only need to adjust one needle a fraction of a turn to get it back to it's optimal settings.
I assume that your understand the basics of a RC Nitro Engine and how it works, if not please see my other articles which you can find on my website, see the resource box for details.
The Idle Screw
I always start with the idle screw, I adjust it so that the car will idle high when I'm first dialing in the engine. Once I get the engine up to temperature and with a tube that can keep it running without stalling I slowly adjust the idle down to the point where it's about to stall, then I turn it back about 1/4 to 1/2 turn depending on the temperature. If your car stalls often it can be worth while increasing the idle to prevent this, it's only a temporary fix while you sort out the other tuning issue, but it helps keep frustration levels down.
Low Speed Needle.
One of the great debates is which needle to adjust first, if your carburetor only has one needle adjustment screw then it's not a problem, but if like most glow engines you have two you need to decide which to tune first. I always start with the low speed needle, this is because when you adjust the low speed needle you change the high speed needle. Once the low speed needle is dialed in you shouldn't have to adjust it again. Make sure you keep it slightly on the rich side, when you RC Car idles the combustion chamber should start to fill up with fuel, this helps keep it cool. After a while the engine will stall, by measuring this you can tell if it should be richer or leaner. A good time is about 30 - 60 seconds before it stalls. The RC Car should pull off quickly from a standing start and should not bog down or flame out when you apply full throttle.
High Speed Needle.
Once you have your low speed adjustment needle dialed in it's time to start getting the power out of the RC engine. This is done with the high speed needle, which adjusts the air to fuel mixture of the engine while it as high RPM (about 40% and up). Keep an eye on the trail of smoke as this is your first clue about the tune. You want to have a lot of smoke coming out of the engine at all RPM, if at some point there is little or no smoke then you are running too lean.
Hints, Tips and Tricks
Turn the needle clockwise to lean out and counter-clockwise to richen the mixture.
A lot of smoke means you tune is rich.
The sound can tell you about your tune.
Reading your glow plug after a run will tell you a lot about your tune.
Make sure to run your engine on the rich side, this will extend it's life.
A lean engine will always put out more power, but it will shorten the life of your engine.
Temperature, air pressure and humidity play if big part in the tune, different days will need different settings.
I assume that your understand the basics of a RC Nitro Engine and how it works, if not please see my other articles which you can find on my website, see the resource box for details.
The Idle Screw
I always start with the idle screw, I adjust it so that the car will idle high when I'm first dialing in the engine. Once I get the engine up to temperature and with a tube that can keep it running without stalling I slowly adjust the idle down to the point where it's about to stall, then I turn it back about 1/4 to 1/2 turn depending on the temperature. If your car stalls often it can be worth while increasing the idle to prevent this, it's only a temporary fix while you sort out the other tuning issue, but it helps keep frustration levels down.
Low Speed Needle.
One of the great debates is which needle to adjust first, if your carburetor only has one needle adjustment screw then it's not a problem, but if like most glow engines you have two you need to decide which to tune first. I always start with the low speed needle, this is because when you adjust the low speed needle you change the high speed needle. Once the low speed needle is dialed in you shouldn't have to adjust it again. Make sure you keep it slightly on the rich side, when you RC Car idles the combustion chamber should start to fill up with fuel, this helps keep it cool. After a while the engine will stall, by measuring this you can tell if it should be richer or leaner. A good time is about 30 - 60 seconds before it stalls. The RC Car should pull off quickly from a standing start and should not bog down or flame out when you apply full throttle.
High Speed Needle.
Once you have your low speed adjustment needle dialed in it's time to start getting the power out of the RC engine. This is done with the high speed needle, which adjusts the air to fuel mixture of the engine while it as high RPM (about 40% and up). Keep an eye on the trail of smoke as this is your first clue about the tune. You want to have a lot of smoke coming out of the engine at all RPM, if at some point there is little or no smoke then you are running too lean.
Hints, Tips and Tricks
Turn the needle clockwise to lean out and counter-clockwise to richen the mixture.
A lot of smoke means you tune is rich.
The sound can tell you about your tune.
Reading your glow plug after a run will tell you a lot about your tune.
Make sure to run your engine on the rich side, this will extend it's life.
A lean engine will always put out more power, but it will shorten the life of your engine.
Temperature, air pressure and humidity play if big part in the tune, different days will need different settings.
Related Tags: guide, gas, engine, power, rc, howto, tuning, tune, nitro, glow, 2-stroke
Gregory Alexander is an RC enthusiast, he spends most of his time racing and drifting RC Cars, more advanced guides and tutorials can he found on The Ultimate RC Drift Resource Site Your Article Search Directory : Find in Articles
Recent articles in this category:
- Avebury Stone Circle - Does It Have Magical Powers?
Avebury is the site of an ancient monument consisting of a large henge. Its construction was spread - How To Successfully Manage Your Digital Photo Collection And Prevent Catastrophic Loss
Wow.... talk about digital explosion, progress in leaps and bounds. In just a space of 20 years we h - A Short But Fascinating Look At Tin Lunch Boxes
Tin lunch boxes went through a great period of revolution throughout the central part of the last ce - Buy A Unexpected Gift Not Your Normal Gifts
No matter what the personality of the person is, you can always opt for the personalized gift sets t - Laser Tattoo Removal Facts To Know
Untold numbers of folks, perhaps even more, walk around having tattoos. A few are visible, some are - The Reason For High Tattoo Removal Costs
Occasionally, you really need to need some thing really bad in your life to put up with the costs th - Honey Bee Magic - Controlling Taste, Texture, And Flavor
There is a great deal of pride that you get from making your own honey, plus it usually tastes bette - Toy Model Trains; The Coming Of Age.
Did You Or your children grow up with Thomas the Tank Engine? Did you ever read them the story of "T - Most Popular Woodworking Crafts And Projects To Do
Is it finally time for the yearly vacation? It's always very hard to wait for the vacation to take p - Scientifically Proven To Add Years To Your Life Keep Your Mind Active And Even Expand Grey Matter
Do it yourself homemade projects have always fascinated me and I always have something on the go.My
Most viewed articles in this category:
- Scientists Today are using Satellite Photos More for Humanitarian Need Rather Than Espionage
Have you ever had the opportunity of seeing real life satellite photos? Well, in the past few weeks, - Japanese Kanji symbol translation for your tattoo.
There are three types of Japanese symbols to choose from when considering a Japanese style tattoo. K - Holly 'red Beauty' (ppaf #14750)
>A Compact, Disease Resistant Holly - 22 Years in the Making! Dr. Elwin Orton of Rutgers University - Miroslav Klabal is an Art Dealer With a Difference
Giving a vent to one's feelings and expressions is not an easy task. Art is one form that can be mad - Find your Favorite Online Casinos
The interest of gamblers in online casinos is constantly on the increase and so is the number of cas - Understanding Dress Up Games
Some parents are concerned about their daughter's safety online. They wonder as she sits down at the - Ingredient of Indonesian Dishes
INGREDIENTS OF INDONESIAN DISHES Indonesia dishes are amongst the most delicious in the world, - Bass Fishing - Learn the Facts That Can Help you Catch the Trophies
In the fishing world largemouth bass and smallmouth bass are two of the more highly coveted fish ind - Giclee Prints - Affordable Fine Art
"Giclee" is a style of fine art, which incorporates the use of modern day printers, predominately 7- - Beach Decorating for Adults and Kids; From Bathroom Décor to Beach Dioramas
One way to bring back memories of a summer at the beach is through beach themed decorating. It is al