Windows 2003 Installing and Configuring an Authoritative Ntp Network Time Server


by Richard n Williams - Date: 2008-07-01 - Word Count: 654 Share This!

Precision and time synchronisation is highly important for modern computer networks, without synchronisation many time sensitive transactions would be impossible to carry out.

The internal clock in computers does keep time and date information but these Real Time Chips are not designed to keep perfect time as computers are mass produced and optimized for low cost rather than being perfect clocks.

Of course for a lot of applications this can be more than adequate but for time-sensitive transactions such as online purchasing not having a network that is synchronised can cause errors in transactions and can even leave the network vulnerable to fraud.

Fortunately Windows Server from 2000 onwards has a time synchronisation utility built in call windows time (w32time.exe) this can be configured to allow the machine to be used as time server.

Windows time uses a form of NTP (Network Time Protocol) which was developed over 20 years ago. It uses an algorithm to synchronise time on a network. NTP (version 4) can maintain time over the public Internet to within 10 milliseconds (1/100th of a second) and can perform even better over LANs with accuracies of 200 microseconds (1/5000th of a second) under ideal conditions.

NTP uses a single time reference and synchronises all machines on the network to that time. It can be configured to both synchronise a network using the internal clock or an external time source.

Note: Microsoft strongly recommends that you configure a time server with a hardware source rather than from the internet where there is no authentication.

To configure the Windows Time service to use an external time source, click Start, Run and type regedit then click OK.

Locate the subkey:

HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeParameters

Right-click Type then Modify, in edit Value type NTP in the Value data box then OK.

Right click ReliableTimeSource, then click Modify.

In the Edit DWORD Value box, under Value Data, type 0, then click OK.

Right-click NtpServer in the right pane then click Modify.

In Edit Value, type the Domain Name System (DNS), each DNS must be unique.

Now click Ok.

To set the poll intervals locate:

HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeParameters

In the right pane, right-click Period, then click Modify.

In the Edit DWORD Value box, under Value Data, type 24 then OK

Exit Registry Editor

Click Start, then Run then type the following and press Enter:

Net stop w32time && net start w32time

Network Time Protocol (NTP) is an Internet protocol used for the transfer of accurate time, providing time information along so that a precise time can be obtained

To enable the Network Time Protocol; NTPserver, locate and click:

HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeTimeProvidersNtpServer

In the right pane, right-click Enabled, then click Modify.

In the Edit DWord Value box, type 1 under Value data, then click OK.

Now go back and click on

HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeParametersNtpServer

In the right pane, right-click NtpServer, then Modify, in the Edit DWORD Value under Value Data type In the right pane, right-click NtpServer, then Modify, in the Edit DWORD Value under Value Data type the Domain Name System (DNS), each DNS must be unique and you must append 0x1 to the end of each DNS name otherwise changes will not take effect.

Now click Ok.

Locate and click the following

HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32TimeTimeProvidersNtpClientSpecialPollInterval

In the right pane, right-click SpecialPollInterval, then click Modify.

In the Edit DWORD Value box, under Value Data, type the number of seconds you want for each poll, ie 900 will poll every 15 minutes, then click OK.

To configure the time correction settings, locate:

HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32Timeconfig

In the right pane, right-click MaxPosPhaseCorrection, then Modify, in the Edit DWORD Value box, under Base, click Decimal, under Value Data, type a time in seconds such as 3600 (an hour) then click OK.

Now go back and click:

HKEY_LOCAL_MACHINESYSTEMCurrentControlSetServicesW32Timeconfig

In the right pane, right-click MaxNegPhaseCorrection, then Modify.

In the Edit DWORD box under base, click Decimal, under value data type the time in seconds you want to poll such as 3600 (polls in one hour)

Exit Registry Editor

Now to restart windows time service, click Start, Run (or alternatively use the command prompt facility) and type:

net stop w32time && net start w32time

And on each computer, other than the time server, type:

W32tm/ -s and the time server should be up and running

 

 


Related Tags: ntp server, gps ntp server, windows ntp server, ntp clock, ntp time server, gps time server, network time server, gps ntp time server, ntp servers, ntp gps time server, windows server 2008, ntp gps server

Richard N Williams is a technical author and a specialist in the telecommunications and network time synchronisation industry helping to develop dedicated NTP clocks. Please visit us for more information about NTP or other network time server solutions.

Your Article Search Directory : Find in Articles

© The article above is copyrighted by it's author. You're allowed to distribute this work according to the Creative Commons Attribution-NoDerivs license.
 

Recent articles in this category:



Most viewed articles in this category: