Breaking-in A Rc Nitro 2-stroke Glow Engine
- Date: 2008-08-23 - Word Count: 730
Share This!
Preparing your Nitro RC Engine only takes a few hours, but the benefits are worth the investment in time. In a nut shell RC 2-stroke engine use a tapered sleeve to create compression, while most full scale cars use piston rings. The process of breaking the engine in is to make sure that the piston and the sleeve have the best fit possible. Like all things RC it just depends on who you ask about breaking-in an engine.
From experience I can tell you that all the methods work well, when in doubt refer to the manual, they will have break-in procedures specific to your engine. the only important thing to remember is not to be too harsh on the engine, break it in slowly taking your time. Remember your not racing yet...
The 7 Step Break in Procedure
While most people recommend running about 5 tanks of fuel through the engine I generally like to run 7, I just like to make sure that I get the engine broken-in correctly. If you look at the oil that comes out the exhaust you'll see that by the 5th or sixth run the tiny bits of metal will be gone from the flow, initially you can see the engine breaking-in from the oil and unburnt fuel.
Needle Settings
Refer to your manual for the specific settings for your engine. The problem is that because each RC Nitro Engine is different you can't just copy your buddies settings, you have to work these out. Break in settings must be as rich as possible, this keep the engine cool and the excess fuel and oil will help flush out the tiny metal bits that come off during the break-in.
Fuel Tank #1
I'll idle the engine for the entire tank, you often need to keep the throttle open about 10% during the first few minutes, at least while the engine warms up. Keep the revs as low as possible, but don't change the mixture needle settings just yet. Once the tank is complete let the engine cool down for about 5 - 15 minutes. Be sure to leave the piston at dead bottom center while it cools, or else the shrinking sleeve could cause a problem if the piston is also there.
Fuel Tank #2
After the initial idle stage I'll run the car with as little throttle as possible, but keep the car moving, I make sure when I accelerate (not more than 25%) I'll do it smoothly and consistently. It's important to start putting some load on the engine, because when you race your RC Car there will be load on the engine. Try to match your break in conditions to your expected running conditions as closely as possible. The idea is to slowly build up the revs of your engine until your able to hit max speed by the end of the 7 th tank. Run your car in a figure-8, as turning makes the engine work slightly harder. After the 2nd Tank you can start to lean your motor out a little.
Fuel Tank #3 -#5
Now we're ready to start getting some speed out of your RC Nitro Car. What I do is start to run the car up and down a long straight, with figure-8 patterns at a low idle between them. I will run at max 25% throttle for about a minute, then rev the RC car flat out for at most 2 seconds. then return to a the standard max 25% throttle. Make sure you get your car to rev right through it's range, but don't keep it at full throttle for too long.
Fuel Tank #5 - #7
I continue as above, but shortening the periods between the bursts of full throttle. I also start to work out the tune of my car, I only change the air / fuel mixture before the 5th tank if I'm struggling to keep the engine running. After the 5th tank I start to lean the mixture by 1/8th turn. I still like to run it until there are no small metal bits in the exhaust discharge.
Once your done with the above break-in procedure I would still run my RC Car gently for the first couple of times on the track, this will ensure that you get the most life our of your brand new RC Nitro Engine.
From experience I can tell you that all the methods work well, when in doubt refer to the manual, they will have break-in procedures specific to your engine. the only important thing to remember is not to be too harsh on the engine, break it in slowly taking your time. Remember your not racing yet...
The 7 Step Break in Procedure
While most people recommend running about 5 tanks of fuel through the engine I generally like to run 7, I just like to make sure that I get the engine broken-in correctly. If you look at the oil that comes out the exhaust you'll see that by the 5th or sixth run the tiny bits of metal will be gone from the flow, initially you can see the engine breaking-in from the oil and unburnt fuel.
Needle Settings
Refer to your manual for the specific settings for your engine. The problem is that because each RC Nitro Engine is different you can't just copy your buddies settings, you have to work these out. Break in settings must be as rich as possible, this keep the engine cool and the excess fuel and oil will help flush out the tiny metal bits that come off during the break-in.
Fuel Tank #1
I'll idle the engine for the entire tank, you often need to keep the throttle open about 10% during the first few minutes, at least while the engine warms up. Keep the revs as low as possible, but don't change the mixture needle settings just yet. Once the tank is complete let the engine cool down for about 5 - 15 minutes. Be sure to leave the piston at dead bottom center while it cools, or else the shrinking sleeve could cause a problem if the piston is also there.
Fuel Tank #2
After the initial idle stage I'll run the car with as little throttle as possible, but keep the car moving, I make sure when I accelerate (not more than 25%) I'll do it smoothly and consistently. It's important to start putting some load on the engine, because when you race your RC Car there will be load on the engine. Try to match your break in conditions to your expected running conditions as closely as possible. The idea is to slowly build up the revs of your engine until your able to hit max speed by the end of the 7 th tank. Run your car in a figure-8, as turning makes the engine work slightly harder. After the 2nd Tank you can start to lean your motor out a little.
Fuel Tank #3 -#5
Now we're ready to start getting some speed out of your RC Nitro Car. What I do is start to run the car up and down a long straight, with figure-8 patterns at a low idle between them. I will run at max 25% throttle for about a minute, then rev the RC car flat out for at most 2 seconds. then return to a the standard max 25% throttle. Make sure you get your car to rev right through it's range, but don't keep it at full throttle for too long.
Fuel Tank #5 - #7
I continue as above, but shortening the periods between the bursts of full throttle. I also start to work out the tune of my car, I only change the air / fuel mixture before the 5th tank if I'm struggling to keep the engine running. After the 5th tank I start to lean the mixture by 1/8th turn. I still like to run it until there are no small metal bits in the exhaust discharge.
Once your done with the above break-in procedure I would still run my RC Car gently for the first couple of times on the track, this will ensure that you get the most life our of your brand new RC Nitro Engine.
Related Tags: gas, engine, rc, radio, petrol, controlled, sleeve, nitro, glow, break-in, piston
Gregory Alexander has been racing and Drifting Nitro Powered RC Cars for several years, he is a lead member of Karnage RC and Drift Club. More RC Tips and Tricks can be found here : The Ultimate RC Drift Resource Site Your Article Search Directory : Find in Articles
Recent articles in this category:
- Avebury Stone Circle - Does It Have Magical Powers?
Avebury is the site of an ancient monument consisting of a large henge. Its construction was spread - How To Successfully Manage Your Digital Photo Collection And Prevent Catastrophic Loss
Wow.... talk about digital explosion, progress in leaps and bounds. In just a space of 20 years we h - A Short But Fascinating Look At Tin Lunch Boxes
Tin lunch boxes went through a great period of revolution throughout the central part of the last ce - Buy A Unexpected Gift Not Your Normal Gifts
No matter what the personality of the person is, you can always opt for the personalized gift sets t - Laser Tattoo Removal Facts To Know
Untold numbers of folks, perhaps even more, walk around having tattoos. A few are visible, some are - The Reason For High Tattoo Removal Costs
Occasionally, you really need to need some thing really bad in your life to put up with the costs th - Honey Bee Magic - Controlling Taste, Texture, And Flavor
There is a great deal of pride that you get from making your own honey, plus it usually tastes bette - Toy Model Trains; The Coming Of Age.
Did You Or your children grow up with Thomas the Tank Engine? Did you ever read them the story of "T - Most Popular Woodworking Crafts And Projects To Do
Is it finally time for the yearly vacation? It's always very hard to wait for the vacation to take p - Scientifically Proven To Add Years To Your Life Keep Your Mind Active And Even Expand Grey Matter
Do it yourself homemade projects have always fascinated me and I always have something on the go.My
Most viewed articles in this category:
- Scientists Today are using Satellite Photos More for Humanitarian Need Rather Than Espionage
Have you ever had the opportunity of seeing real life satellite photos? Well, in the past few weeks, - Japanese Kanji symbol translation for your tattoo.
There are three types of Japanese symbols to choose from when considering a Japanese style tattoo. K - Holly 'red Beauty' (ppaf #14750)
>A Compact, Disease Resistant Holly - 22 Years in the Making! Dr. Elwin Orton of Rutgers University - Miroslav Klabal is an Art Dealer With a Difference
Giving a vent to one's feelings and expressions is not an easy task. Art is one form that can be mad - Find your Favorite Online Casinos
The interest of gamblers in online casinos is constantly on the increase and so is the number of cas - Understanding Dress Up Games
Some parents are concerned about their daughter's safety online. They wonder as she sits down at the - Ingredient of Indonesian Dishes
INGREDIENTS OF INDONESIAN DISHES Indonesia dishes are amongst the most delicious in the world, - Bass Fishing - Learn the Facts That Can Help you Catch the Trophies
In the fishing world largemouth bass and smallmouth bass are two of the more highly coveted fish ind - Giclee Prints - Affordable Fine Art
"Giclee" is a style of fine art, which incorporates the use of modern day printers, predominately 7- - Beach Decorating for Adults and Kids; From Bathroom Décor to Beach Dioramas
One way to bring back memories of a summer at the beach is through beach themed decorating. It is al